Fresh Air Restoration & Cleaning — water, mold, air ducts, San Antonio TX
(210) 982-0647

Air Duct Mold Removal · San Antonio · TDLRMold In The Ducts. Handled Once.

Licensed mold remediation and certified duct cleaning from the same crew — so spores don't ride back in through the vents.

Black mold on the wall and floor of a utility closet

Two Trades, One Crew

Mold in a wall and mold in a mechanical system are different jobs with different rules. We hold both TDLR credentials required to remediate mold in Texas and RIA certification in Mechanical Systems Hygiene, so the remediation and the duct work are handled by one crew on one schedule.

  • TDLR Mold Remediation Company #RCO0176
  • TDLR Mold Remediation Contractor #MRC0212
  • ASCR/RIA certified in Mechanical Systems Hygiene
  • Remediating mold in Texas since licensing began in 2004
  • One point of contact — no second contractor to coordinate
Mold growth on insulated piping in a commercial mechanical room

2004

Licensed for mold remediation since Texas started licensing it.

Find It. Contain It. Clean The System.

Mold gets into an air handler through standing condensate, a failed drain pan or humidity the system cannot pull down. Treat the growth and leave the cause and it comes back — so the moisture source and the mechanical system are both part of the scope.

  • Inspection and sampling before the scope is set
  • Moisture source identified and documented
  • Sealed containment and negative air at the air handler
  • HEPA filtration throughout the work
  • Whole-system cleaning — supply, return, trunk lines, plenum, coil and blower
  • Antimicrobial treatment of the system interior
  • Written documentation for clearance testing or your insurance carrier
Technician inside a sealed containment with a negative-air machine and HEPA vacuum

What to Expect

  1. 1

    Tell Us What You See

    Tell us what you see and when the odor began. A musty smell when the air conditioning kicks on and something dark around a register are often the same problem caught at different stages.

  2. 2

    Inspection Before the Scope

    If you can see growth, start with an inspection rather than a cleaning. Inspection and sampling come before the scope is set, and you get the scope in writing.

  3. 3

    Find the Moisture Source

    Mold gets into an air handler through standing condensate, a failed drain pan or humidity the system cannot pull down. The moisture source is identified and documented.

  4. 4

    Contain and Clean the Whole System

    Sealed containment and negative air go up at the air handler, with HEPA filtration throughout the work. Then the whole system is cleaned: supply, return, trunk lines, plenum, coil and blower. The system interior gets an antimicrobial treatment.

  5. 5

    Documentation You Can Use

    You get written documentation for clearance testing or your insurance carrier. The remediation and the duct work are handled by one crew on one schedule.

Air Duct Mold Removal Questions

Is this a duct cleaning or a mold remediation?

Mold in a duct system is both. A duct cleaning is maintenance. It does not come with containment, clearance documentation, or a protocol written for a third-party test. Remediation is the controlled removal of active growth. We scope both sides together on these jobs.

Can a regular duct cleaning remove mold?

Not on its own. If there is active mold growth in the system, cleaning alone can move spores around the house rather than remove the problem. Clean the system and leave the moisture source, and it comes back, usually within a season.

How does mold get into ductwork?

Through moisture. Mold gets into an air handler through standing condensate, a failed drain pan or humidity the system cannot pull down. The air handler is dark, it holds condensate, and in a San Antonio summer it runs for months pulling humid air across a cold coil.

The house smells musty but I can't see mold. What then?

If the only symptom is a musty smell, there has been no water event you know about, and nothing is visible at the registers, the likely answer is a cleaning plus a hunt for the moisture source. Smell without visible growth is usually dust, biofilm around the drain pan, or something that got wet once and dried.

What licenses cover this work?

In Texas, mold remediation is licensed work. We hold TDLR Mold Remediation Company #RCO0176 and Contractor #MRC0212, and have since Texas began licensing mold remediation in 2004. Our duct-cleaning side is certified separately, through ASCR and RIA in Mechanical Systems Hygiene.

Will the mold come back?

Treat the growth and leave the cause and it comes back, so the moisture source and the mechanical system are both part of the scope. Some homes benefit from UV-C at the coil to slow regrowth between cleanings.

Need help today?

We answer 24/7/365 and dispatch from San Antonio.

Financing available — click here to apply · Ask about our Whole-House Allergy Treatment

Call Now Free Estimate